波谱学杂志 ›› 2025, Vol. 42 ›› Issue (3): 299-307.doi: 10.11938/cjmr20253148cstr: 32225.14.cjmr20253148

• 磁共振仪器与技术专栏 • 上一篇    下一篇

宽频磁共振微线圈设计

江超超, 姚守权, 徐俊成, 蒋瑜*()   

  1. 华东师范大学 物理与电子科学学院,上海市磁共振重点实验室,上海200062
  • 收稿日期:2025-02-27 出版日期:2025-09-05 在线发表日期:2025-03-27
  • 通讯作者: * Tel: 021-62233871, E-mail: yjiang@phy.ecnu.edu.cn.
  • 基金资助:
    上海市科技创新行动计划资助项目(19142202900);国家自然科学基金资助项目(21874045)

Design of the Broadband Magnetic Resonance Microcoil

JIANG Chaochao, YAO Shouquan, XU Juncheng, JIANG Yu*()   

  1. Shanghai Key Laboratory of Magnetic Resonance, School of Physics and Electronic Science, East China Normal University, Shanghai 200062, China
  • Received:2025-02-27 Published:2025-09-05 Online:2025-03-27
  • Contact: * Tel: 021-62233871, E-mail: yjiang@phy.ecnu.edu.cn.

摘要:

微量样品检测在环境监测、生物科学和医学等领域具有广泛的应用需求.使用常规磁共振探头对微量样品进行检测时,由于线圈的填充因子较小,导致磁共振检测信噪比降低.采用与微量样品尺寸相当的微线圈进行检测可显著提高探测灵敏度,增强信噪比.此外,由于磁共振宽频探测的需求不断增长,人们希望在样品检测过程中减少实验步骤以缩短检测时间.因此,设计能够覆盖更宽频率范围的磁共振微型线圈变得至关重要.目前市场上的商用宽频探头并非针对微量样品检测而设计,且均为调谐探头,探头电路较为复杂,难以满足高效、便捷的应用需求.针对以上问题,本研究设计了一个多层板螺线管结构微线圈,其射频场均匀性良好,且电感和电阻均较小.利用有限元分析软件对线圈结构进行了优化,并采用印刷电路板(Printed Circuit Board,PCB)技术研制.在1.5 T磁共振成像系统磁体下,利用自研的谱仪及宽频射频前端,对250 nL的不同样品进行了测试,实现了氢核(1H)、氘核(2H)、锂核(7Li)和氟核(19F)等多种元素的磁共振探测.实验结果证明该线圈具有良好的宽频性能.

关键词: 核磁共振, 微线圈, 宽频, 印刷电路板

Abstract:

The detection of microsamples holds extensive application demands in fields such as environmental monitoring, biological sciences, and medicine. When conventional magnetic resonance probes are used to detect microsamples, the smaller filling factors lead to reduced signal-to-noise ratios (SNR) in magnetic resonance detection. Using microcoils comparable in size to the microsamples can significantly improve detection sensitivity and enhance SNR. Furthermore, due to the growing demand for broadband detection, there is a desire to reduce experimental steps during sample analysis and shorten detection times. However, currently available commercial probes are not designed for microsample detection and are relatively too complex to meet the requirements for efficient and convenient applications. To address these issues, this study designed a multilayer solenoid microcoil with excellent field uniformity, low inductance, and resistance. The coil was fabricated using printed circuit board (PCB) technology and tested on a 1.5 T MRI system magnet equipped with a self-developed spectrometer and broadband RF front end, where multiple nuclei (1H, 2H, 7Li, 19F) were detected in 250 nL samples, demonstrating broadband capability and high sensitivity. The results highlight its potential for efficient and versatile microsample analysis.

Key words: nclear magnetic resonance (NMR), microcoil, broadband, printed circuit board (PCB)

中图分类号: